Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
projekte:epson-stylus-sx100 [2016-06-04 03:02] – [Contact Image Sensor] crackiprojekte:epson-stylus-sx100 [2017-01-17 01:01] (current) – external edit 127.0.0.1
Line 7: Line 7:
 Uebrig sind: Uebrig sind:
  
-  * Contact Image Sensor mit LEDs+  * [[projekte:contact_image_sensor|Contact Image Sensor]] mit LEDs
   * Schrittmotor (96 Schritte, 18 Ohm, ~0.2-0.3 Ampere)   * Schrittmotor (96 Schritte, 18 Ohm, ~0.2-0.3 Ampere)
   * zwei DC Motoren, vmtl brushed   * zwei DC Motoren, vmtl brushed
Line 16: Line 16:
  
 Beschriftungen: FC11B913F56 F KTH0351-2 Beschriftungen: FC11B913F56 F KTH0351-2
 +
 +Numerierung:
 +  * Rohm: Pin 1 aussen.
 +  * PCB: Pin 1 innen <- die nehmen wir
 +
 +==== Beleuchtung ====
  
 Die LEDs brauchen so 2-3 Volt, Strom ~20 mA bringt schon Licht. Die LEDs brauchen so 2-3 Volt, Strom ~20 mA bringt schon Licht.
Line 21: Line 27:
 die TO Pins am PCB sind: V+, Blau, Rot, Gruen. die TO Pins am PCB sind: V+, Blau, Rot, Gruen.
  
-NumerierungPin 1 aussen.+Bei 5V Versorgung sollte mit folgenden Widerständen nach Erde gezogen werden fuer weisses PapierRot:50, Grün:50, Blau:220.
  
 +<pagebreak>
 Spannung 1 mA: Spannung 1 mA:
-^ + \ - ^  ^  10 11 12 ^ Beschreibung des Pins ^ +^ + \ - ^  ^     ^ Beschreibung des Pins ^ 
-|     |  x |    |    | LED + +|     |  x |          |    | N/C (so weit sich erkennen laesst) 
-|     |    |  x |    |    |    | LED GND Blau +|     |    |  x |    |    |    | LED GND Rot 
-   10 |    |    |  x |    |    | LED GND Gruen | +    3 |    |    |  x |    |    | LED GND Gruen | 
-   11 |    |    |    |  x |    | LED GND Rot +    4 |    |    |    |  x |    | LED GND Blau 
-   12 |    |          |  x | N/C (so weit sich erkennen laesst) |+    5 |    |    |  x | LED + | 
 + 
 +==== Datensignale ====
  
 Spannung 1 mA: Spannung 1 mA:
-^ + \ - ^    ^    ^    ^             ^ Beschreibung des Pins ^ +^ + \ - ^    ^    ^    ^      10   11   12 ^ Vias ^ Geometrie  ^ relativ ^ Vermutung ^ Beschreibung des Pins ^ 
-|     |    x | <typo bg:#bbb2ff>1.84</typo> | <typo bg:#b9b2ff>1.83</typo> | <typo bg:#b2f4ff>1.50</typo> | <typo bg:#bbb2ff>1.84</typo> | <typo bg:#ffe0b2>0.61</typo> | <typo bg:#bbb2ff>1.84</typo>duenne Bahn, ueber der unteren Flaeche, unter #11, Via/Segment +|     |    x | <typo bg:#ffe0b2>0.61</typo> | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#b2f1ff>1.51</typo> | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#bdb2ff>1.85</typo> | 1    | dünn               | Startpuls | zwischen oberer Flaeche und Schrauben 
-|     | <typo bg:#bdb2ff>1.85</typo> |    x | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#b2f1ff>1.51</typo> | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#ffe0b2>0.61</typo> | <typo bg:#bdb2ff>1.85</typo>duenne Bahn, unter der Mittleren Flaeche, ueber #12, 1 Via/Segment +|     | <typo bg:#b2ffcc>1.22</typo> |    x | <typo bg:#b2ffe6>1.34</typo> | <typo bg:#caffb2>0.99</typo> | <typo bg:#b2ffe6>1.34</typo> | <typo bg:#b2ffe6>1.34</typo> | <typo bg:#b2ffe4>1.33</typo>2    | breit      | oben    | 3V3       
-|     | <typo bg:#b9b2ff>1.83</typo> | <typo bg:#bbb2ff>1.84</typo> |    x | <typo bg:#b2f4ff>1.50</typo> | <typo bg:#bbb2ff>1.84</typo> | <typo bg:#ffe0b2>0.61</typo> | <typo bg:#bbb2ff>1.84</typo>breite Flaeche mitte, wo die Schrauben durchgehen (aber kein kontakt). Via/Segment +|     | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#ffe0b2>0.61</typo> |    x | <typo bg:#b2f1ff>1.51</typo> | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#b6b2ff>1.82</typo> | 1    | dünn               | Clock     | von unten hochstechend 
-|     | <typo bg:#ffb2b2>0.40</typo> | <typo bg:#ffb4b2>0.41</typo> | <typo bg:#ffb4b2>0.41</typo> |    x | <typo bg:#ffb4b2>0.41</typo> | <typo bg:#ffb2bd>0.35</typo> | <typo bg:#ffb4b2>0.41</typo>breite Flaeche untenueber #8, 3-5 Vias je Segment +|     | <typo bg:#ffb4b2>0.41</typo> | <typo bg:#ffb2bd>0.35</typo> | <typo bg:#ffb4b2>0.41</typo> |    x | <typo bg:#ffb4b2>0.41</typo> | <typo bg:#ffb4b2>0.41</typo> | <typo bg:#ffb2b2>0.40</typo>3-5  | breitestes | unten   | GND       ueber #8 | 
-    5 | <typo bg:#b6b2ff>1.82</typo> | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#b2f1ff>1.51</typo> |    x | <typo bg:#ffe0b2>0.61</typo> | <typo bg:#bdb2ff>1.85</typo>duenne Bahn, Via je Segment von unten hochstechend +   10 | <typo bg:#bbb2ff>1.84</typo> | <typo bg:#ffe0b2>0.61</typo> | <typo bg:#bbb2ff>1.84</typo> | <typo bg:#b2f4ff>1.50</typo> |    x | <typo bg:#bbb2ff>1.84</typo> | <typo bg:#b9b2ff>1.83</typo> | 1    | breit      | mitte   | Vref      | driftet langsam, wenn Versorgung angeklemmt (andere pins sind nah an GND) 
-    6 | <typo bg:#b2ffe4>1.33</typo> | <typo bg:#b2ffe6>1.34</typo> | <typo bg:#b2ffe6>1.34</typo> | <typo bg:#caffb2>0.99</typo> | <typo bg:#b2ffe6>1.34</typo> |    x | <typo bg:#b2ffcc>1.22</typo>breite Flaeche ganz oben2 Vias je Segment +   11 | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#ffe0b2>0.61</typo> | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#b2f1ff>1.51</typo> | <typo bg:#bdb2ff>1.85</typo> |    x | <typo bg:#bdb2ff>1.85</typo>1    | dünn               | 300/600 dpi | unter der Mittleren Flaeche, ueber #12 
-    7 | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#b2f1ff>1.51</typo> | <typo bg:#bdb2ff>1.85</typo> | <typo bg:#ffe0b2>0.61</typo> |    x | duenne Bahn zwischen oberer Flaeche und Schrauben1 Via je Segment |+   12 | <typo bg:#bbb2ff>1.84</typo> | <typo bg:#ffe0b2>0.61</typo> | <typo bg:#bbb2ff>1.84</typo> | <typo bg:#b2f4ff>1.50</typo> | <typo bg:#b9b2ff>1.83</typo> | <typo bg:#bbb2ff>1.84</typo> |    x | 1    | dünn               | Aout       | ueber der unteren Flaeche, unter #11 |
  
-Widerstand: +==== Insgesamt ====
-^ + \ - ^    1 ^    2 ^    3 ^    4 ^    5 ^    6 ^    7 ^ +
-|     1 |    x |      |      |      |      |      |      | +
-|     2 |      |    x |      |      |      |      |      | +
-|     3 |      |      |    x |      |      |      |      | +
-|     4 |      |      |      |    x |      |      |      | +
-|     5 |      |      |      |      |    x |      |      | +
-|     6 |      |      |      |      |      |    x |      | +
-|     7 |      |      |      |      |      |      |    x | +
- +
-Vermutungen: +
-  * 4,6: Versorgung +
-  * 1,2,3,5,7: Daten+
  
 sieht verdammt nach [[http://rohmfs.rohm.com/en/products/databook/datasheet/module/contact_image_sensor/flatbed/lsh3008-ca10a.pdf]] aus sieht verdammt nach [[http://rohmfs.rohm.com/en/products/databook/datasheet/module/contact_image_sensor/flatbed/lsh3008-ca10a.pdf]] aus
 +
 +  * 6 Startpuls
 +  * 8 Clock
 +  * 10 Vref (sollte auf GND fest)
 +    * wenns hoeher ist, gibts kein gescheites bild mehr
 +  * 11 DPI Mode
 +    * macht auf jeden Fall, wieviele Clocks man pro Zeile rausholen kann
 +    * 0/L: 300 dpi ~2600 clocks
 +    * 1/H: 600 dpi ~5268 clocks
 +    * nach anderen datenblaettern hat man 82 clocks "output period", dann kommen die pixel (inkl. vorne und hinten dummypixeln)
 +    * 600 dpi: 5184 pixels
 +    * 300 dpi: 2592 pixels
 +  * 12 Analog Out
 +    * bei steigender Clock gehts scheinbar los (kommt von GND hoch fuer jeden Pixel neu, gefuehlte 100ns hier)
 +    * bei fallender Clock sampeln klingt sinnvoll
 +
 +==== Operation ====
 +
 +Startpuls wird bei fallender Clock gesampelt. Wenn Startpuls, dann werden die Werte in den Ausgabepuffer geschickt. Dann mit Clock rauscyceln. Belichtungszeit haengt wohl vom Intervall zwischen Startpulsen ab.
 +
 +Was ich mache (funktioniert, kann man bestimmt noch reduzieren):
 +
 +  * Werte -> Shiftregister, neue Belichtung starten:
 +    * Puls hoch
 +    * Clock hoch
 +    * warte 500us
 +    * Clock runter
 +    * warte 500us
 +    * Puls runter
 +  * Shiftregister rausholen:
 +    * Clock rauf (Signal geht los)
 +    * warte 1us
 +    * Clock runter (Signal sollte stabil sein, kann man sampeln)
 +    * warte 1us
 +    * so oft wie es pixel gibt
 +  * restliche Belichtungszeit geben
 +    * warte, 0-20 Millisekunden haben geklappt
 +
 +==== Arduino ====
 +
 +<code>
 +#define START 2
 +#define CLOCK 3
 +#define DPIMODE 4
 +
 +bool dpimode = 1;
 +uint16_t pixels = dpimode ? 5184 : 2592;
 +
 +uint32_t linetime = 20000; // us
 +uint32_t sched = 0;
 +
 +void setup() {
 +  pinMode(START, OUTPUT);
 +  pinMode(CLOCK, OUTPUT);
 +  pinMode(DPIMODE, OUTPUT);
 +
 +  digitalWrite(DPIMODE, dpimode);
 +
 +  sched = micros();
 +}
 +
 +void loop() {
 +  digitalWrite(START, HIGH);
 +  digitalWrite(CLOCK, HIGH);
 +  digitalWrite(CLOCK, LOW);
 +  digitalWrite(START, LOW);
 +
 +  for (uint16_t counter = 0; counter < 82 + pixels; counter += 1)
 +  {
 +    PORTD |= _BV(PORTD3);
 +    //delayMicroseconds(1);
 +    PORTD &= ~_BV(PORTD3);
 +    //delayMicroseconds(1);
 +  }
 +
 +  sched += linetime;
 +  int32_t dt = sched - micros();
 +  while (dt > 0x4000)
 +  {
 +    delayMicroseconds(0x4000);
 +    dt -= 0x4000;
 +  }
 +  if (dt > 0)
 +    delayMicroseconds(dt);
 +}
 +</code>
 ==== coloring code ==== ==== coloring code ====
 <code> <code>
Line 74: Line 157:
 open("foo.txt", "w").write(rex.sub(colorize, source)) open("foo.txt", "w").write(rex.sub(colorize, source))
 </code> </code>
 +
 +==== Bilder ====
 +
 +{{projekte:sx100:img_20160604_004626.jpg?500|}}
 +
 +{{projekte:sx100:img_20160604_004801.jpg?500|}}
 +
 +{{projekte:sx100:img_20160604_004821.jpg?500|}}
 +
 +
Navigation



You are not allowed to add pages