Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
projekte:epson-stylus-sx100 [2016-06-04 20:43]
cracki [Arduino]
projekte:epson-stylus-sx100 [2016-06-15 00:56]
cracki [epson-stylus-sx100]
Line 7: Line 7:
 Uebrig sind: Uebrig sind:
  
-  * Contact Image Sensor mit LEDs+  * [[projekte:​contact_image_sensor|Contact Image Sensor]] mit LEDs
   * Schrittmotor (96 Schritte, 18 Ohm, ~0.2-0.3 Ampere)   * Schrittmotor (96 Schritte, 18 Ohm, ~0.2-0.3 Ampere)
   * zwei DC Motoren, vmtl brushed   * zwei DC Motoren, vmtl brushed
Line 16: Line 16:
  
 Beschriftungen:​ FC11B913F56 F KTH0351-2 Beschriftungen:​ FC11B913F56 F KTH0351-2
 +
 +Numerierung:​
 +  * Rohm: Pin 1 aussen.
 +  * PCB: Pin 1 innen <- die nehmen wir
 +
 +==== Beleuchtung ====
  
 Die LEDs brauchen so 2-3 Volt, Strom ~20 mA bringt schon Licht. Die LEDs brauchen so 2-3 Volt, Strom ~20 mA bringt schon Licht.
Line 21: Line 27:
 die TO Pins am PCB sind: V+, Blau, Rot, Gruen. die TO Pins am PCB sind: V+, Blau, Rot, Gruen.
  
-Numerierung: +Bei 5V Versorgung sollte mit folgenden Widerständen nach Erde gezogen werden fuer weisses PapierRot:50, Grün:50, Blau:220.
-  * RohmPin 1 aussen. +
-  * PCBPin 1 innen <- die nehmen wir+
  
 <​pagebreak>​ <​pagebreak>​
Line 33: Line 37:
 |     4 |    |    |    |  x |    | LED GND Blau | |     4 |    |    |    |  x |    | LED GND Blau |
 |     5 |    |  R |  G |  B |  x | LED + | |     5 |    |  R |  G |  B |  x | LED + |
 +
 +==== Datensignale ====
  
 Spannung 1 mA: Spannung 1 mA:
Line 43: Line 49:
 |    11 | <typo bg:#​bdb2ff>​1.85</​typo>​ | <typo bg:#​ffe0b2>​0.61</​typo>​ | <typo bg:#​bdb2ff>​1.85</​typo>​ | <typo bg:#​b2f1ff>​1.51</​typo>​ | <typo bg:#​bdb2ff>​1.85</​typo>​ |    x | <typo bg:#​bdb2ff>​1.85</​typo>​ | 1    | dünn       ​| ​        | 300/600 dpi | unter der Mittleren Flaeche, ueber #12 | |    11 | <typo bg:#​bdb2ff>​1.85</​typo>​ | <typo bg:#​ffe0b2>​0.61</​typo>​ | <typo bg:#​bdb2ff>​1.85</​typo>​ | <typo bg:#​b2f1ff>​1.51</​typo>​ | <typo bg:#​bdb2ff>​1.85</​typo>​ |    x | <typo bg:#​bdb2ff>​1.85</​typo>​ | 1    | dünn       ​| ​        | 300/600 dpi | unter der Mittleren Flaeche, ueber #12 |
 |    12 | <typo bg:#​bbb2ff>​1.84</​typo>​ | <typo bg:#​ffe0b2>​0.61</​typo>​ | <typo bg:#​bbb2ff>​1.84</​typo>​ | <typo bg:#​b2f4ff>​1.50</​typo>​ | <typo bg:#​b9b2ff>​1.83</​typo>​ | <typo bg:#​bbb2ff>​1.84</​typo>​ |    x | 1    | dünn       ​| ​        | Aout       | ueber der unteren Flaeche, unter #11 | |    12 | <typo bg:#​bbb2ff>​1.84</​typo>​ | <typo bg:#​ffe0b2>​0.61</​typo>​ | <typo bg:#​bbb2ff>​1.84</​typo>​ | <typo bg:#​b2f4ff>​1.50</​typo>​ | <typo bg:#​b9b2ff>​1.83</​typo>​ | <typo bg:#​bbb2ff>​1.84</​typo>​ |    x | 1    | dünn       ​| ​        | Aout       | ueber der unteren Flaeche, unter #11 |
 +
 +==== Insgesamt ====
  
 sieht verdammt nach [[http://​rohmfs.rohm.com/​en/​products/​databook/​datasheet/​module/​contact_image_sensor/​flatbed/​lsh3008-ca10a.pdf]] aus sieht verdammt nach [[http://​rohmfs.rohm.com/​en/​products/​databook/​datasheet/​module/​contact_image_sensor/​flatbed/​lsh3008-ca10a.pdf]] aus
Navigation



You are not allowed to add pages